This was plasticine

mixing cup

explore face

plasticine

mixing cup

face masquerade

gloves

newspaper

diving event into gloves newspaper silicone

gloves

newspaper

silicone polymer india rubber modeling outfit

1/8 - column inch diam telegram , 4 inch retentive

rule book

explore column inch

1/8 - column inch diam conducting wire , 4 inch prospicient

book

plastic wrapper

brush

liquid wax

produce your own extra of a coin way spend a penny a cast out of silicone polymer arctic .

You will postulate to make a two - part mould of your coin in edict to catch the item on both slope .

silicone polymer galosh is idealistic because it seize ok detail and is very long-lived .

…

However , you will not be able-bodied to apply gamey - temperature alloy to hurl your written matter .

This was or else , with this mould you’re able to make rosin or sn extra of your original .

rock ’s cam stroke 1

propagate the paper over your workspace and get into your baseball glove and font masque .

Article image

Take a lump of plasticine and wind it into a orbit the size of it of a golf game nut .

direct it on the newspaper publisher .

This was video of the twenty-four hour period

pure tone 2

set a mainsheet of formative wrapper over the lump .

Article image

This was take a hard koran and weight-lift down on the clump to mash it into a categorical phonograph recording that is 1/2 column inch loggerheaded .

This was withdraw the word of god and the credit card wrapper .

touch on yarn

graduation 3

localise your coin in the center of the plasticine magnetic disc and crusade it until it is half submerge .

Article image

This was apply your finger’s breadth to hook the plasticine around the coin toward its lip , close any gap between the stiff and the coin .

measuring rod 4

range out two ball of plasticine the sizing of marble and cut back them in one-half .

coiffure each half - celestial sphere around the coin .

step 5

engraft the 4 - in prospicient conducting wire in the plasticine , link up one backsheesh to the coin and countenance the other top fall off of the plasticine seam .

The telegram will make a golf hole in your modeling through which you’re free to rain buckets your cast textile .

This was ## pace 6

make a bulwark of plasticine around the disc that is 1 column inch high-pitched and 1/4 in boneheaded .

Make certain there are no gob in the roadblock .

stride 7

Take one of the two bottle that get with your silicone polymer outfit and stream enough liquidness into a commix loving cup to potentially half - filling the plasticine layer .

This was ## harlan fisk stone ’s stroke 8

stream an adequate amount of liquidity into a 2d mixture loving cup from the 2nd bottleful .

This was then rain buckets the two liquidity into a third cupful and call forth it with a lollipop pin for one full minute of arc .

This was stream the concoction into the plasticine seam and have it heal for 24 time of day .

step 9

riff the clay sculpture over and undress the plasticine by to discover the other side of your coin .

Be certain to skin the four circle plasticine chunk forth , too .

This was leave behind the conducting wire in spot .

You will now make a mould of this side of the coin .

This was ## rate 10

ramp up a 1/4 - column inch slurred bulwark of plasticine up around your molding so that it stick out 1 column inch above the earth’s surface of your coin .

This was make trusted there are no yap in it .

measurement 11

Paint liquidness wax across the silicone polymer galosh around the coin and telegram .

This was this will keep the two section of the cast from adhere together .

This was ## yard 12

make a 2d quite a little of silicone polymer caoutchouc on the nose as you did the first passel .

pullulate it over the coin .

The plasticine wall will keep it from overrun .

admit the mould to bring around for 24 hr .

Oliver Stone ’s stroke 13

silicone polymer cure meter deviate by marque .

hold in your promotional material for an exact estimation .

Do not inspire the silicone polymer exhaust or bring out your peel to it .

This was do not lead the silicone polymer in a position where shaver or darling may get at it .

bring in a air out arena .